Molicel P42A and P28A: high-drain cells for power tools and scooters. Compared with EVE 40P, Samsung 50S, 30Q and 25R
Share
The 18650 and 21700 cell catalogue has two families. High-capacity cells such as the Samsung 35E or LG M58T store a lot of energy but do not like high currents. High-drain cells have less capacity, but deliver power without overheating and without a large voltage drop under load. They are the choice for drills, grinders, mowers, scooters and powerful bikes.
Two cells that are the benchmark in this category have joined our range: the Molicel P42A and the Molicel P28A, alongside the power tool classic, the Samsung 25R. We compare them with the high-drain cells we already stock and show how to choose the right one for your project.
Comparison in one table
Data from the manufacturers' datasheets. Price per Wh calculated from typical capacity and a voltage of 3.6 V.
| Cell | Format | Capacity | Continuous current | Charging current (std / max) | Price | PLN per Wh |
|---|---|---|---|---|---|---|
| Molicel P42A | 21700 | 4200 mAh | 45 A | 4.2 A | PLN 15.49 | 1.02 |
| EVE 40P | 21700 | 4000 mAh | 40 A | max. 6 A | PLN 13.90 | 0.97 |
| Samsung 50S | 21700 | 5000 mAh | 25 A (45 A with 80°C cut-off) | max. 6 A | PLN 19.99 | 1.11 |
| Molicel P28A | 18650 | 2800 mAh | 35 A | 2.8 / 8.4 A | PLN 14.90 | 1.48 |
| Samsung 25R | 18650 | 2500 mAh | 20 A | 1.25 / 4.0 A | PLN 10.49 | 1.17 |
| Samsung 30Q | 18650 | 3000 mAh | 15 A | 1.5 / 4.0 A | PLN 13.90 | 1.29 |
The continuous current in the datasheet is a limit value measured under laboratory conditions, often with a high-temperature cut-off. A pack is not designed for that value. How to translate it into a real design is explained below.
Molicel P42A: the most versatile high-drain 21700 cell
The P42A combines 4200 mAh (4000 mAh minimum) with a continuous current of 45 A and an AC resistance of about 10 mΩ. In practice this means that at a 10-20 A load it loses little voltage and heats up little. The datasheet shows about 90% capacity after 500 cycles at a 10 A discharge. It is a cell for powerful scooters, bikes with 1500-3000 W drives, robots and professional power tools.
Compared with the EVE 40P the difference is small: the P42A has about 5% more capacity and slightly higher current, the 40P is cheaper. If the pack is limited by space, choose the P42A. If by budget, the 40P. The Samsung 50S has clearly more capacity, but heats up more at continuous currents above about 20 A, so it works better in packs where high currents are short-lived.
Molicel P28A: the 18650 that replaces the 30Q and 25R
The P28A answers the question of what to put into a power tool battery that originally had 2000-2500 mAh 18650 cells. It gives 2800 mAh (2700 mAh minimum) and 35 A of continuous current, i.e. more capacity than the 25R and more current than the 30Q. It also has the highest permissible charging current in this comparison: 8.4 A, which matters with fast tool chargers.
The Samsung 25R, in turn, is the economical choice. 20 A of continuous current is enough for most drivers and vacuum cleaners, and the price is the lowest in the comparison. It comes from a 2026 batch. The Samsung 30Q has the most capacity of the three (3000 mAh) but the lowest current (15 A). You will find a wider comparison of 18650 cells, including high-capacity ones, in the article Samsung 35E vs 30Q vs LG M29.
How to calculate current per cell
The whole method fits into two formulas:
Pack current = power ÷ nominal pack voltage
Current per cell = pack current ÷ number of cells in parallel (P)
You compare the result with the continuous current in the datasheet. A practical rule used by pack designers: for long life and low temperature, keep the continuous current per cell around half of the datasheet value, and leave values close to the maximum for short peaks.
Example 1: 36 V, 1000 W power tool
A 10S pack (36 V), current about 28 A. In a 10S2P configuration each cell delivers about 14 A.
- Molicel P28A: 14 A is 40% of 35 A. The cell works with a large margin.
- Samsung 25R: 14 A is 70% of 20 A. It will work, but the pack will heat up noticeably during long use.
- Samsung 35E: 14 A against a permissible 8 A. Not suitable.
Example 2: 48 V, 2000 W scooter or bike
A 13S pack (48 V), current about 42 A. In a 13S4P configuration each cell delivers about 10.4 A.
- Molicel P42A: about 23% of the rated current. Pack 16.8 Ah, about 806 Wh.
- EVE 40P: about 26%. Pack 16 Ah, about 768 Wh.
- Samsung 50S: about 42%. Pack 20 Ah, about 960 Wh, but with less thermal headroom.
- Samsung 50E: 10.4 A against a permissible 9.8 A. A 13S4P pack on this cell is not suitable for a 2000 W drive. It would need 13S5P or larger.
This shows the whole trade-off. High-capacity cells give more Wh for the same number of cells, but at high power you have to add more of them to bring the current per cell down. High-drain cells let you build a smaller, lighter pack with the same power. Which option wins depends on whether your project is short of space or of range. A comparison of the formats with calculations can be found in the 18650 or 21700 guide.
And if range matters: EVE 50E
Not every project needs a high-drain cell. If you are building a pack for a bike with 250-750 W assist, a portable energy storage unit or power for a robot with a steady, moderate draw, a high-capacity cell will do better. The new EVE INR21700-50E in our range has 5000 mAh, a continuous current of 15 A and one of the lowest prices per Wh among our 21700 cells (about PLN 0.66). Its weaker side is the charging current: the datasheet gives 1 A as standard and 2.5 A as the continuous maximum, which must be taken into account when choosing a charger. For large stationary storage, LiFePO4 chemistry works better, as we describe in our guide to batteries built from EVE LF105 cells. We compare the other high-capacity cells in the article Samsung 53G vs 50E vs 50S vs LG M58T.
Charging high-drain cells
High-drain cells usually handle faster charging well too. The P28A allows 8.4 A, the P42A has a standard current of 4.2 A. A 13S4P pack on P42A can therefore accept about 17 A (4 × 4.2 A) on the cell side. Whether it actually can depends on the BMS and the socket. How to calculate this and which 54.6 V charger to choose is shown in our guide how to choose the charging current for a 48 V battery.
The 2022 Molicel batch: what it means
The Molicel P42A and P28A cells we offer come from a batch produced in 2022 (warehouse stock), and we state this in the product description. A Li-ion cell stored at partial charge and moderate temperature ages slowly, but not at zero rate. That is why, for cells from longer storage, we recommend three simple checks before assembly:
- Measure the resting voltage of all cells. Group cells with similar voltages in the same parallel section.
- If you have a tester, measure the internal resistance and compare it with the datasheet (P42A: about 10 mΩ AC, P28A: max. 20 mΩ AC).
- For larger packs, run a capacity test on a sample of a few cells.
How a new cell from warehouse stock differs from a cell from disassembly is explained in the article new vs pulled cells.
Which cell to choose: quick cheat sheet
| Application | First choice | Alternative |
|---|---|---|
| Refurbishing an 18650 power tool battery | Molicel P28A | Samsung 25R (budget) |
| Driver, vacuum cleaner, light tool | Samsung 25R | Samsung 30Q (more capacity) |
| Scooter and bike 1500-3000 W | Molicel P42A | EVE 40P (budget) |
| 21700 pack with high capacity and current peaks | Samsung 50S | Molicel P42A |
| Assisted bike, energy storage, moderate current | EVE 50E | cells from the 21700 comparison |
Frequently asked questions
Is the Molicel P42A better than the Samsung 50S?
At high continuous current, yes, because it has almost twice the rated current in continuous operation and heats up less. The Samsung 50S, on the other hand, has about 19% more capacity. For packs whose power is sized with a margin, the 50S will give more range.
Can I mix cells of different models in one pack?
No. All cells in a pack should be the same model, from the same batch and with similar parameters. Mixing models leads to uneven operation of the sections and faster degradation.
Can I replace the 35E cells in a bike battery with P42A to get more power?
They are two different formats (18650 and 21700), so they will not fit the same holders. Besides, pack power is also limited by the BMS, the wiring and the controller. Without upgrading to a stronger BMS, new cells will not give more power.
Is a regular 3500 mAh cell enough for a power tool?
For a light tool with a low draw, sometimes yes, but not for hammer drills, grinders and saws. High-capacity cells lose a lot of voltage and heat up quickly at 15-20 A, and the tool loses power and shuts down sooner.
Summary
A high-drain cell is chosen when the current per cell exceeds about half of what a high-capacity cell can handle. In the 21700 format the most versatile choice is the Molicel P42A, with the EVE 40P as a budget alternative. In the 18650 format the Molicel P28A performs best for power tools, and the cheapest sensible option is the Samsung 25R.
You will find all the cells in the 18650 cells and 21700 cells collections. Not sure which cell fits your project? Write to us with the voltage, power and available space.

Article author
Marcin Świder
Co-founder of evzero.eu